Is VG10 a good steel for kitchen knives?
Short answer: Yes, VG10 steel is one of the most dependable stainless steels for kitchen knives: Takefu Special Steel’s cobalt-alloyed grade takes a keen edge at around HRC 60–61, holds it well and is easy to sharpen. Does VG10 rust? Rarely with sensible care, but salt, acid or a soak in the sink can still leave small spots, which come off easily if you catch them early.
Key takeaways
- VG10 (“V Gold 10”) is made by Takefu Special Steel of Echizen, Fukui. Knife Steel Nerds dates it to around 1959, and many Japanese knife makers use it, including Tojiro.
- Takefu lists about 1% carbon, 15% chromium, 1% molybdenum, 0.25% vanadium and 1.5% cobalt, and recommends a hardness of HRC 60 or above.
- It is stainless, not stain-proof: salt, acid and standing water can leave small rust spots, usually near the edge or the handle.
- Light spots come off with a little cream cleanser on a soft sponge or a rust eraser; never use wire wool or a metal scourer.
- Edge retention is good rather than exceptional. Powder steels such as SG2 last longer between sharpenings, but VG10 is quicker and easier to sharpen.
- Most chips come from bones, frozen food, twisting or hard boards rather than from the steel.
What is VG10 steel?
VG10 (V金10号 in Japanese, also written VG-10) is a stainless cutlery steel made by Takefu Special Steel, a steelmaker in Echizen, Fukui, founded in 1954 and best known for laminated knife steel. Metallurgist Larrin Thomas of Knife Steel Nerds, going by Takefu’s description of it as developed more than 60 years ago, dates it to around 1959. Takefu recommends a hardness of HRC 60 or above, and most VG10 kitchen knives sit at 60–61, including our Tojiro DP VG10 range at HRC 60±1.
| Element | VG10 (Takefu representative value) | What it contributes |
|---|---|---|
| Carbon | 1.00% | Allows high hardness and forms hard carbides |
| Chromium | 15.00% | Rust resistance, plus chromium carbides for wear resistance |
| Molybdenum | 1.00% | Strength and extra corrosion resistance |
| Vanadium | 0.25% | Refines the microstructure |
| Cobalt | About 1.5% | Helps the steel resist softening at high temperature |
The cobalt is unusual in a stainless knife steel. Knife Steel Nerds suggests it was added for tempering resistance, so that VG10 keeps its hardness when coatings are applied to blades at high temperature. Takefu also warns that counterfeit and similar steels are sold under names such as “VG TEN”, so buy from a retailer who can tell you who made the knife.
Does VG10 rust?
VG10 is a genuine stainless steel. In Knife Steel Nerds’ “is it stainless?” test, four days of distilled-water spray, it showed no corrosion at all, and in a harsher 1% salt-water test it performed about as its chromium and molybdenum content predicts. Knife Steel Nerds rates its corrosion resistance 7.9 out of 10, almost level with SG2 at 7.8, and it is far more rust-resistant than carbon steels such as Aogami or Shirogami.
But stainless means stain-resistant, not stain-proof. Tojiro, which makes VG10 knives, warns that salt or acid left on a blade, for example after cutting pickles or lemons, can cause rust, as can long storage somewhere humid or leaving a knife in a washing-up bowl. On VG10, rust usually shows up as tiny orange-brown specks near the edge or where the blade meets the handle. VG10 won’t develop the protective patina that carbon steel does, so treat any discolouration as something to remove rather than keep.
How to stop VG10 rusting
- Wipe the blade during prep when cutting salty or acidic food such as citrus, tomatoes, pickles or cured meat.
- Wash it by hand with a soft sponge and washing-up liquid soon after use. Never soak it or put it in the dishwasher.
- Dry it completely, including the spine and the join with the handle.
- Store it somewhere dry and ventilated, such as a magnetic rack, block or sheath, and never put it away damp.
What should you do if your VG10 knife has rust spots?
Spots on VG10 are usually light surface rust, and the sooner you deal with them, the easier they are to remove:
- Wash the blade with washing-up liquid to remove any food residue, then dry it.
- Rub the spot gently with a little cream cleanser on a soft sponge, as Tojiro recommends, keeping your fingers clear of the edge.
- For stubborn spots or staining, use a rust eraser, then rinse.
- Don’t reach for wire wool or a metal scourer: Tojiro warns that hard scrubbers can scratch the blade.
- If rust has reached the cutting edge, re-sharpening on a whetstone removes it, as Tojiro also suggests. For deeper spots or pitting, our rust removal service starts from £6.
- Wash and dry the knife again, then look for the cause: food left on the blade, a damp drawer or a soak in the sink.
For more detail, see How do I remove rust from a Japanese knife?
How sharp does VG10 get, and how long does the edge last?
At HRC 60–61, VG10 takes a fine, keen edge that suits the thin, double-bevel geometry of Japanese knives. In CATRA slicing tests reported by Knife Steel Nerds, its edge retention came out a small notch below 440C, in line with its chromium carbide content. In plain terms, that is good, dependable edge life for home cooking, but not class-leading: powder steels such as SG2 (R2) have more wear resistance and go longer between sharpenings, usually at a higher price.
The trade-off is easy maintenance. VG10’s carbides are mostly chromium carbides, with very little of the harder vanadium carbide that slows sharpening in some “super steels”, and Knife Steel Nerds describes it as relatively easy to polish, similar to 440C. Any decent whetstone will sharpen it: a 1000/6000 combination stone covers regular sharpening and refining. As a rough guide, Tojiro suggests sharpening about once or twice a month; see How often should I sharpen or strop my Japanese knife?
Is VG10 prone to chipping?
VG10 has a reputation in some circles for being chippy, but testing doesn’t single it out. In Knife Steel Nerds’ toughness tests, with both steels at about HRC 60.7, VG10 averaged 5.8 ft-lbs against 6.5 for the powder steel SG2: slightly behind, and in line with other high-carbide stainless steels. Most chips on Japanese knives come from the combination of a hard, thin edge and the wrong job: cutting through bone or frozen food, twisting the blade in a squash, or using a glass or stone board.
Use a wooden or synthetic board, let the knife slice rather than lever, and reach for a cleaver for bones. Small chips can be sharpened out, and our repair service removes chips from £6. See also Do Japanese knives chip easily?
How does VG10 compare with other knife steels?
| Steel | Type | Typical hardness | Rust resistance | Best for |
|---|---|---|---|---|
| VG10 | Stainless (Takefu) | HRC 60–61 | High, but can spot if left wet or salty | A low-maintenance all-rounder that is easy to sharpen |
| AUS10 | Stainless (Aichi Steel) | HRC 60±1 in our range | High; slightly less chromium and molybdenum than VG10 | Very similar everyday performance |
| SG2 / R2 | Powder stainless | HRC 62–64 | High; close to VG10 in testing | Longer edge life, if you treat a thin, hard edge with care |
| Shirogami / Aogami | Carbon steel | HRC 62±1 on our Sakamoto Santoku | Low: dry it at once; it develops a patina | Cooks happy to look after a reactive blade |
For more detail, see VG10 vs AUS10 and our guide to stainless, carbon, powder and damascus steels.
Our recommendation
Prices below are at the time of writing (October 2026).
- Best value: the Tojiro Basic 3 Layer VG10 Gyuto 210mm has a VG10 core clad in 13-chrome stainless steel, HRC 60±1 and no bolster, for under £60. The same construction comes as a Santoku 170mm and a Nakiri 165mm.
- The classic: the Tojiro DP VG10 Gyuto uses 3-layer VG10 at the same hardness, with a bolster and a laminated handle, in 180–300mm, from just over £100.
- Damascus looks: the Yasuo 69 Layers Gyuto (180/210mm, HRC 60±1, made in Seki), the Yasuo Black Bunka (165/200mm, HRC 61±1), the Kiyotsu VG10 33 Layer Santoku 165mm with a hammered tsuchime finish, and the Saku 69 Layer Santoku 175mm (under £90).
- Small knives: the Tojiro Classic Damascus Petty in 120 or 150mm (VG10, HRC 61±1).
How Japanese Knife Company can help
You can try VG10 knives with guidance in the knife studio at our London shops in Baker Street, Greek Street, Kensington, Chiswick and Wimbledon. Every knife bought from us includes one complimentary sharpening; after that, our whetstone sharpening and repair service costs £1.35 per inch for domestic double-bevel knives, with rust removal and chip removal each from £6, in store or by post. If you would rather learn to do it yourself, our two-hour, hands-on knife sharpening class for beginners has no more than six people per group.
Related questions
- Will my Japanese knife rust, stain, or develop a patina over time?
- How do I remove rust from a Japanese knife?
- VG10 vs AUS10: which steel is better?
- Is SG2 (R2) steel hard to sharpen?
- Tojiro DP vs Tojiro Basic: which should I buy?
Sources
- Takefu Special Steel – VG10
- Knife Steel Nerds – VG10 and Super Gold 2: Takefu Stainless Steel Properties and History
- TOJIRO – Sharpening and care (研ぎ方・お手入れ)
- Aichi Techno Metal Fukaumi – High-strength stainless steel (AUS series)
Reviewed by the Japanese Knife Company team, October 2026.