VG10 vs AUS10: which steel is better?
Short answer: VG10 vs AUS10 is a close contest: both are Japanese stainless steels with about 1% carbon, typically hardened to around HRC 60. Takefu’s VG10 adds more chromium and molybdenum plus cobalt, so on paper it resists corrosion and wear slightly better, while Aichi Steel’s leaner AUS10 is very close in everyday use. Heat treatment and blade geometry matter more.
Key takeaways
- VG10 comes from Takefu Special Steel in Echizen, Fukui; AUS10 from Aichi Steel in Tōkai, Aichi, whose AUS sheet is rolled by Aichi Techno Metal Fukaumi.
- Both have roughly 1% carbon. VG10 adds about 15% chromium, 1% molybdenum and 1.5% cobalt; AUS10 has 13–14.5% chromium, 0.1–0.3% molybdenum and no cobalt.
- The makers’ reference hardness is almost identical (HRC 60 or more for VG10, about HRC 60 for AUS10), and both are HRC 60±1 in our range.
- Both are low in vanadium, so both sharpen quickly on ordinary whetstones.
- Price follows the knife rather than the steel: in our range, VG10 and AUS10 gyutos sit in similar price bands.
- Choose on grind, handle, balance and price rather than on the steel name alone.
VG10 vs AUS10 at a glance
| Factor | VG10 | AUS10 | Verdict |
|---|---|---|---|
| Hardness in our range | HRC 60±1 | HRC 60±1 | Draw |
| Edge retention | Slightly more chromium carbide on paper | Very close | Slight edge to VG10; geometry matters more |
| Toughness | Reasonable for a stainless steel in independent testing | No independent like-for-like test found | Too close to call |
| Ease of sharpening | Quick on ordinary whetstones | Quick on ordinary whetstones | Draw |
| Rust resistance | More chromium and molybdenum | Leaner alloy | VG10, on paper |
| Price in our range (October 2026) | Tojiro Basic gyuto under £60; Tojiro DP gyuto from just over £100 | JKC AUS10 gyuto around £110–£130 | Set by the knife, not the steel |
What are VG10 and AUS10?
VG10 (“V Gold 10”) is a cobalt-alloyed stainless cutlery steel developed by Takefu Special Steel, the Echizen steelmaker best known for laminated knife steel. Takefu recommends a hardness of HRC 60 or above and highlights its long-lasting edge, corrosion resistance and ease of sharpening.
AUS10 belongs to Aichi Steel’s AUS series of blade steels. Aichi groups the series with its 13% chromium stainless steels and explains that the AUS-6M, AUS-8 and AUS-10 grades add more carbon, plus vanadium and molybdenum, for greater hardness, wear resistance and resistance to softening. AUS-10 has the most carbon of the three and is used for high-quality knives, scissors and medical instruments. Aichi’s AUS sheet is rolled by Aichi Techno Metal Fukaumi, which publishes the specification below.
VG10 vs AUS10: composition and hardness compared
| Property | VG10 | AUS10 |
|---|---|---|
| Steelmaker | Takefu Special Steel (Echizen, Fukui) | Aichi Steel (Tōkai, Aichi) |
| Carbon | 1.00% | 0.95–1.10% |
| Chromium | 15.00% | 13.00–14.50% |
| Molybdenum | 1.00% | 0.10–0.30% |
| Vanadium | 0.25% | 0.10–0.25% |
| Cobalt | About 1.5% | None listed |
| Maker’s hardness | HRC 60 or higher | About HRC 60 (reference value) |
| In our range | Tojiro DP and Basic, Yasuo 69 Layers (HRC 60±1) | JKC AUS10 (HRC 60±1) |
VG10 figures are Takefu’s representative values; AUS10 figures are specification ranges from Aichi Techno Metal Fukaumi. Minor elements are omitted. Our steel chemistry page covers other grades.
Which holds an edge longer?
Both steels get most of their wear resistance from chromium carbides, with only small vanadium additions. With more chromium and molybdenum, VG10 should form slightly more of these carbides, giving it a small advantage in wear resistance on paper. Knife Steel Nerds found VG10’s slicing edge retention a small notch below that of 440C, in line with its chromium carbide content.
In the kitchen, other factors usually swamp that difference. Knife Steel Nerds’ analysis of CATRA slicing tests identifies edge angle as a very strong controlling factor in edge life, alongside hardness and carbide content, so a thin, well-sharpened AUS10 knife can outlast a thicker VG10 one. Neither steel matches powder steels such as SG2 for edge life.
Which is easier to sharpen, and which is tougher?
Sharpening is a draw. Neither steel contains much vanadium carbide, the very hard particles that slow sharpening in some “super steels”, and Knife Steel Nerds describes VG10 as relatively easy to polish, similar to 440C. AUS10’s vanadium is just as low (0.10–0.25%), so expect both to respond quickly to an ordinary 1000-grit whetstone.
Toughness is harder to call. Knife Steel Nerds measured VG10 at 5.8 ft-lbs at about HRC 60.7, in line with other high-carbide stainless steels, but we know of no independent, like-for-like toughness test of AUS10 against it, so treat claims that one is far tougher with caution. At HRC 60±1 on thin Japanese geometry, both will chip if twisted in bone or frozen food.
Which resists rust better?
On paper, VG10. It has more chromium (15% against 13–14.5%) and much more molybdenum (1% against 0.1–0.3%), and molybdenum is particularly helpful against the pitting that salt can cause. Both are genuine stainless steels and will stay rust-free with normal care: wash by hand, dry straight away, and never leave them in the dishwasher or a washing-up bowl. Either can show small spots if left wet with salty or acidic food.
Why do other sources disagree about VG10 and AUS10?
Search for this comparison and you’ll find different numbers for the same two steels. There are three main reasons:
- Hardness is set by the knifemaker, not just the steel. Some retailers list AUS10 a point softer than VG10, but Aichi’s reference hardness for AUS-10 is HRC 60, and both steels are HRC 60±1 in the knives we sell.
- Compositions get copied and garbled. Rely on the steelmakers’ own figures, as in our table: Takefu’s representative values for VG10 and Aichi Techno Metal Fukaumi’s specification ranges for AUS-10.
- Performance claims are rarely tested. You’ll see confident statements that one steel holds an edge far longer or is much tougher, but we haven’t found independent, like-for-like tests that compare the two.
Which should you choose?
Because the steels are so close, compare the knives. Prices are at the time of writing (October 2026).
- Western feel and balance: the JKC AUS10 Gyuto (180/210/240mm) has a 3-layer AUS10 blade at HRC 60±1, a brown pakkawood handle, a stainless bolster and a full tang. It is made in Seki by Suncraft and costs around £110–£130, and it suits cooks moving from a German knife. The JKC AUS10 range also includes a 165mm bunka, boning knives and a set of two.
- The VG10 classic: the Tojiro DP VG10 Gyuto pairs a 3-layer VG10 blade (HRC 60±1) with a bolster and a laminated handle, in 180–300mm, from just over £100 to around £240.
- Damascus VG10: the Yasuo 69 Layers Gyuto (180/210mm) adds a hammered 69-layer damascus finish and a pakkawood handle, also at HRC 60±1, made in Seki.
- Tightest budget: the Tojiro Basic 3 Layer VG10 Gyuto 210mm drops the bolster and costs under £60.
What about AUS8?
AUS-8 is the next grade down in Aichi’s AUS series. It has less carbon than AUS-10 (0.70–0.80% against 0.95–1.10%) and a lower reference hardness (HRC 59 against 60), so on paper it is slightly softer and less wear-resistant, at a lower price. Our JKC AUS8 Gyuto 200mm (3 layers, HRC 59±1, full tang, made in Seki by Suncraft) costs under £90, and there is a matching JKC AUS8 Santoku 165mm.
How Japanese Knife Company can help
Holding a knife tells you more about balance and handle feel than any spec sheet, and you can try knives with guidance in the knife studio at our London shops. Every knife bought from us includes one complimentary sharpening, our whetstone sharpening and repair service keeps either steel cutting well, and you can add free engraving on the product page.
Related questions
- Is VG10 a good steel for kitchen knives?
- What is the best Japanese chef’s knife under £100?
- Tojiro DP vs Tojiro Basic: which should I buy?
- What is the difference between stainless steel, carbon steel, VG10, AUS10, Aogami, Shirogami, SG2/R2, and Damascus steel?
- Who makes Japanese Knife Company’s own-brand knives?
Sources
- Takefu Special Steel – VG10
- Aichi Steel – Stainless steel for blades
- Aichi Techno Metal Fukaumi – High-strength stainless steel (AUS series)
- Knife Steel Nerds – VG10 and Super Gold 2: Takefu Stainless Steel Properties and History
- Knife Steel Nerds – Which Steel Has the Best Edge Retention? Part 1
Reviewed by the Japanese Knife Company team, October 2026.