Which oil should I use on my Japanese knife?

Short answer: Camellia oil (tsubaki oil) is the best oil for a Japanese knife: it is the traditional, food-safe choice, light and slow to go sticky. Food-grade mineral oil is a good alternative. Avoid storing knives under ordinary cooking oils, which can turn rancid or tacky. Carbon steel needs a thin coat; stainless rarely needs any.

Key takeaways

  • Camellia oil is pressed from the seeds of the tsubaki (Camellia japonica) in Japan; it is edible and has traditionally been used to protect Japanese swords and carbon steel blades from rust.
  • It is mostly oleic acid, with a low iodine value, so it stays as a thin film instead of drying into a sticky varnish.
  • Food-grade mineral oil works too and doesn’t go rancid, which is why it is also used on chopping boards.
  • Oil matters most for carbon steel such as Aogami and Shirogami, and for storage; stainless knives mainly need washing and drying.
  • Use a few drops, wipe on a thin film, and never oil a wet or rusty blade.

What oil for a Japanese knife works best?

Rust needs water and oxygen, so a blade oil works by leaving a very thin film that keeps them off the steel. For a kitchen knife, that oil should be safe to eat, thin enough to spread into an almost invisible layer, and stable enough not to harden, smell or collect dust.

Camellia oil meets all three. In Japan it is pressed from tsubaki seeds and used in cooking, for tempura, stir-frying and dressings, and it has traditionally been applied to protect Japanese swords and carbon steel blades from rust. A 2019 study in the Journal of Oleo Science found that oleic acid makes up more than 80% of the fatty acids in Camellia japonica seed oil, with an iodine value of 79.9. Oils with an iodine value below 115 are classed as non-drying: unlike linseed oil, they don’t cure into a hard, tacky film.

Can you use olive oil or vegetable oil instead of camellia oil?

In a pinch, yes, but they are not ideal for a knife you store. All plant oils slowly oxidise. Oils rich in polyunsaturated fats, such as sunflower or rapeseed (“vegetable”) oil, react with air more readily and can leave a tacky film, while mostly monounsaturated oils such as olive and camellia are more stable. Olive oil can still go rancid on a blade left for weeks, and extra virgin olive oil brings its own flavour and smell.

Oil Food-safe? Stays thin and non-sticky? Verdict
Camellia (tsubaki) Yes, if sold pure or food-grade Yes: it is a non-drying oil The traditional first choice
Food-grade mineral oil Yes Yes, and it doesn’t go rancid A good, neutral alternative
Olive oil Yes Mostly, but it can go rancid on a stored blade Fine in a pinch
Sunflower, rapeseed or “vegetable” oil Yes Less so: it oxidises faster and can turn tacky Avoid for storage
WD-40, gun or machine oil No – Never on kitchen knives

Check the label before you buy: some “knife oils” are blends, so choose one sold as pure camellia oil or as suitable for food contact.

How much oil should you use, and how often?

Less than you think: a few drops will cover a whole knife. Our care instructions cover everyday cleaning; for oiling:

  1. Wash the knife by hand and dry it completely; water trapped under oil can still cause rust.
  2. Remove any rust spots first, then wash and dry again.
  3. Put two or three drops of oil on folded kitchen paper or a soft cloth, or use an applicator.
  4. Fold the cloth over the spine and wipe from heel to tip with the edge facing away from your fingers, covering both faces, the spine and the area where the blade meets the handle.
  5. Wipe off the excess: the steel should look barely damp, not glossy.
  6. Before you next cook, wipe the blade with a clean cloth, or wash and dry it if you applied a heavier coat for storage.

How often depends on the steel:

  • Carbon steel (Aogami, Shirogami and other non-stainless steels): we suggest oiling after drying whenever the knife will sit unused for more than a day, and more often in a humid kitchen. The patina that develops helps, but it doesn’t replace drying.
  • Stainless-clad carbon steel: the cladding resists rust but the exposed carbon steel edge doesn’t, so treat the edge like carbon steel.
  • Stainless steel (VG10, AUS10, SG2 and similar): no oil is needed day to day. ZWILLING’s care guide suggests a light coat, wiped off with paper, if any knife will go unused for several days.
  • Long storage: apply a slightly heavier coat, wrap each knife separately in paper, and keep it somewhere dry and well ventilated.

Should you oil the handle?

Traditional Japanese (wa) handles are often unfinished magnolia (ho) wood, which can dry out and absorb water. Keep them dry, never put them in the dishwasher, and when the wood looks pale or feels dry, rub in a little camellia or food-grade mineral oil, leave it for a few minutes and wipe off the excess. ZWILLING likewise recommends oiling wooden handles regularly. Resin-impregnated handles such as pakkawood or micarta need little more than washing and drying.

Chopping boards are a separate job. They need far more oil and are best treated with a dedicated board oil or food-grade mineral oil rather than your knife oil.

Our recommendation

How Japanese Knife Company can help

If rust has already taken hold, our sharpening and repair service offers rust removal from £6, alongside traditional whetstone sharpening, in our five London shops (Baker Street, Greek Street, Kensington, Chiswick and Wimbledon) or by post. Every knife bought from us also includes one complimentary sharpening.

Related questions

Sources

Reviewed by the Japanese Knife Company team, October 2026.

0
32