Is SG2 (R2) steel hard to sharpen?

Short answer: No, SG2 (R2) steel is not hard to sharpen on good whetstones; it is simply slower than softer steels such as VG10. Takefu’s Super Gold 2 is a powder stainless steel usually hardened to HRC 62–64, but most of its carbides are chromium carbides that ordinary whetstones cut well. Use quality stones, steady moderate pressure and a careful deburr.

Key takeaways

  • SG2 is Takefu Special Steel’s Super Gold 2; R2 is the name linked to Kobelco (Kobe Steel), and knife makers widely treat the two as the same powder steel.
  • Takefu specifies HRC 62 or higher, and most SG2 kitchen knives sit at 62–64, harder than VG10 at around 60–61.
  • Powder metallurgy gives it fine, evenly spread carbides, good toughness for its hardness and long edge life.
  • It sharpens on standard whetstones: a 1000/6000 combination stone covers routine work, coarse grits are slower, and diamond plates speed up repairs but aren’t essential.
  • At the same hardness SG2 tested slightly tougher than VG10, but thin SG2 blades at HRC 62–64 still chip if they meet bone, frozen food or a hard board.

What is SG2 (R2) steel?

SG2 stands for Super Gold 2, which Takefu Special Steel of Echizen, Fukui, describes as its original high-grade blade steel made by powder metallurgy; Knife Steel Nerds dates its patent to 1991. Instead of being cast in large ingots, powder steel starts as molten steel atomised into fine, rapidly solidified particles, which Takefu then compacts, sinters, forges and rolls. The result is a fine, even spread of carbides: Knife Steel Nerds point-counted about 16.5% carbide by volume in SG2. Takefu, which abbreviates the steel as SPG2, specifies HRC 62 or higher but does not publish the composition. Knife Steel Nerds reports roughly 14–15% chromium, 2–3% molybdenum and 2% vanadium, with carbon near the top of a 0.9–1.5% range.

R2 is the name associated with Kobelco (Kobe Steel): the Zknives steel database says Kobelco apparently supplies R2 to Takefu, which sells it as SG2. The same knives are often labelled R2 in one market and SG2 in another, and neither company publishes a side-by-side comparison, so treat the two names as one steel family. MIYABI uses its own name: ZWILLING describes the core of the MIYABI 5000MCD as MC63 micro carbide powder steel, at around 63 HRC.

Property VG10 SG2 / R2
Made by Takefu Special Steel Takefu Special Steel (sold as SG2); R2 name linked to Kobelco
Production Conventional (non-powder) steel Powder metallurgy
Chromium / molybdenum / vanadium About 15% / 1% / 0.25% About 14–15% / 2–3% / 2%
Maker’s hardness HRC 60 or higher HRC 62 or higher
Typical kitchen knife HRC 60–61 HRC 62–64
Toughness (both tested at about HRC 60.7) 5.8 ft-lbs 6.5 ft-lbs
Corrosion resistance (Knife Steel Nerds rating) 7.9 out of 10 7.8 out of 10
Wear resistance Good Higher than VG10
Sharpening Quick and easy Slower on coarse stones; fine on quality whetstones

Is SG2 steel hard to sharpen?

Two things make a steel feel hard to sharpen: its hardness, and the amount and type of hard carbide particles in it. At HRC 62–64, SG2 is harder than VG10 or a typical German stainless knife, so each stroke removes a little less steel. You notice this most on coarse stones, when you are repairing chips or reshaping a very blunt edge.

The carbides are the reassuring part. Knife Steel Nerds calculates that SG2 contains about 12.8% chromium carbide but only about 0.5% vanadium carbide. Vanadium carbide is harder than aluminium oxide, the most common abrasive in sharpening stones, which is why high-vanadium “super steels” can be slow to sharpen and polish without diamonds. SG2 has less vanadium carbide than steels such as S30V or M390, so it sharpens and polishes well on good conventional stones.

In practice, SG2 trades a slightly longer sharpening session for less frequent sharpening. Its wear resistance is higher than VG10’s, so the edge lasts longer in everyday use, and the fine powder structure takes a very keen, refined edge.

How do you sharpen SG2 without damaging the edge?

  1. Start at the right grit. For a dull but undamaged edge, begin at 1000 grit. Only drop to a coarse stone (around 220–400 grit) to remove chips or reshape the edge, as coarse grits remove steel quickly on any knife.
  2. Keep your stones flat. A dished stone rounds the edge and tip, and hard steel makes the problem easy to see. Flatten your stones regularly with a flattening stone.
  3. Hold a low, steady angle. Around 10–15° per side suits most Japanese double-bevel knives; an angle guide helps you stay consistent.
  4. Use moderate, even pressure. Let the stone do the work. Heavy pressure on a thin, hard edge risks micro-chips and a larger burr.
  5. Raise a burr along the whole edge, then remove it. Work the second side until the burr flips, then make a few lighter alternating strokes, slightly raising the angle if needed, to weaken and remove it. Stropping on leather alone often leaves a burr behind.
  6. Refine and finish. Move to 3000–6000 grit and strop lightly on a leather strop. Test the edge on paper or a tomato, then wash and dry the knife.

Avoid pull-through sharpeners, which are too coarse and aggressive for a thin, hard edge. See also Are rolling knife sharpeners good for Japanese knives?

Which whetstones do you need for SG2?

Job Grit Options in our range
Repairing chips or reshaping a damaged edge Around 220–400, or a diamond stone TOG 320 Coarse, Naniwa Super Stone 400 or a diamond stone
Routine sharpening of a dull edge 1000 1000/3000 combination stone (Naniwa) or 1000/6000 combination stone
Refining the edge 3000–6000 The fine side of the same combination stones
Polishing (optional) 10000 and above Rockstar 10000 or Rockstar 16000

If you buy one stone, make it a 1000/6000 combination; the Naniwa Sharpening Bundle pairs a 1000 and a 6000 stone. Add a coarse stone or a diamond stone when you need to repair chips, and a flattening stone to keep everything true (see Do I need a flattening stone?).

Does SG2 chip more easily than VG10?

Not because of its chemistry. In Knife Steel Nerds’ toughness tests, with both steels heat-treated to about HRC 60.7, SG2 averaged 6.5 ft-lbs against VG10’s 5.8, so at equal hardness it is slightly the tougher of the two. The difference in the kitchen comes from how SG2 knives are made: most are hardened to HRC 62–64 and ground very thin, which leaves a fine, hard edge with little margin for bones, frozen food, twisting cuts or glass and stone boards.

Treat an SG2 knife as a slicer: let it cut rather than lever, use a wooden or synthetic board, and keep a cleaver for bones. Small chips can be sharpened out on a coarse stone, or we can remove them for you from £6, with re-profiling from £12. See also Do Japanese knives chip easily?

What we recommend

  • Takamura Aka SG2: Gyuto 180/210mm and Santoku 165mm in SG2 at around HRC 64 (our listing), with three layers, a very thin and light blade and a red handle; the gyuto is around £230–£240 at the time of writing (October 2026). The thin edge cuts beautifully but is not for bones, frozen food or twisting cuts. See the Takamura Aka SG2 collection.
  • MIYABI 5000MCD: an MC63 micro carbide powder steel core (around 63 HRC, according to ZWILLING) inside 101-layer damascus, with a D-shaped masur birch handle, as a gyuto, a 170mm nakiri and a 130mm utility knife.
  • Kamoshiro SG2 Petty 135mm: an easy way to try SG2 in a small, nimble knife.
  • Saji R2: fully handmade by Takeshi Saji, with an R2 core in 101 layers at HRC 64±1, for collectors and enthusiasts.

How Japanese Knife Company can help

Every knife bought from us comes with one complimentary sharpening, and our whetstone sharpening and repair service is available in all five London shops or by post, at £1.35 per inch for domestic double-bevel knives, with chip removal from £6 and re-profiling from £12. To learn to do it yourself, book our two-hour, hands-on knife sharpening class: it is designed for beginners, with no more than six people per group.

Related questions

Sources

Reviewed by the Japanese Knife Company team, October 2026.

0
26